DCMA

Get link
Facebook
X
Pinterest
Email
Other Apps

DMCA

If we Have added some content that belong to you or your organization by mistake, We are sorry for that. We apologize for that and assure you that this wont be repeated in future. If you are rightful owner of the content used in our Website, Please mail us with your Name, Organising at ion Name, Contact Details, Copyright infringing URL and Copyright Proof (URL or Legal Document) at Himanshu chudhary

I assure you that, I will remove the infringing content Within 48 Hours.

Get link
Facebook
X
Pinterest
Email
Other Apps

Comments

Why should a magnesium ribbon be cleaned before burning in air?

Ques 1 : Why should a magnesium ribbon be cleaned before burning in air? Ans 1: Magnesium is very reactive metal like (Na, C a, etc.). When it expose to air it reacts with oxygen to form a layer magnesium oxide (Mg O) on its surface. Mg + O 2 → 2 Mg O This layer of magnesium oxide is quite stable and prevents further reaction of magnesium with oxygen. The magnesium ribbon is cleaned by sand paper to remove this layer so that the underlying metal can be used for the reaction. «« Chapter 1 NCERT Solution Next question »»

Diagonal Relationship between Beryllium and Aluminium || Relation between Beryllium and Aluminium

Diagonal Relationship between Beryllium and Aluminium The ionic radius of Beryllium (Be 2+) is estimated to be nearly 31 pm; the charge/radius ratio Or e/m ratio is nearly the same as that of the Al 3+ ion. Hence beryllium resembles aluminium in these ways. Some of the similarities are given below: » Like Aluminium, Beryllium(be) is not readily attacked by acids H+ donor because of the formation of an oxide film on the surface of the metal by reacting with oxygen, i.e. they are rendered passive by nitric acid. » Beryllium hydroxide[[Be(OH)4]2] dissolves in excess of alkali to give a beryllate ion, [ Be(OH)4]2– just as aluminium hydroxide[Al(OH)3] gives aluminate ion, [Al(OH)4] » The chlorides of metals beryllium and aluminium have Cl– bridged chloride structure in vapour phase. Both the chlorides are soluble in organic solvents and are strong as Lewis acids They are used as Friedel Craft catalysts. » Beryllium(Be) and aluminium(Al) ions have strong tendency to form complexes, (Be...

Banking of road The maximum permissible velocity with which vehicle can go round a level curved road without skidding depends on the coefficient of friction ( μ) between the tyres and the road The value of μ decreases when road is smooth or tyres of the vehicle are worn out or the road is wet and so on. Thus force of friction is not a reliable source for providing the required centripetal force to the vehicle. A safer course of action would be to raise outer edge of the curved road shove the inner edge. By doing so, a component of normal reaction of the road shall be spared to provide the centripetal force. This phenomenon of raising outer edge of the curved road above the inner edge is called banking of roads . It's facilitates vehicles to turn without slipping. Three forces are acting on the vehicle as shown in Figure below. (i) Weight mg of the vehicle acting vertically downwards. (ii)...

A rocket with a lift-off mass 20,000 kg is blasted upwards with an initial acceleration of 5.0 m/s². Calculate the initial thrust (force) of the blast.

Ques : A rocket with a lift-off mass 20,000 kg is blasted upwards with an initial acceleration of 5.0 m/s². Calculate the initial thrust (force) of the blast. Ans : Mass of the rocket, m = 20,000 kg Initial acceleration, a = 5 m/s2 Acceleration due to gravity, g = 10 m/s2 Using Newton’s second law of motion, the net force (thrust) acting on the rocket is given by the relation: F – mg = ma F = m (g + a) = 20000 × (10 + 5) = 20000 × 15 = 3 × 10^5 N.

Di nitrogen and dihydrogen react with each other to produce ammonia according to the following chemical equation

Ques : Di nitrogen and dihydrogen react with each other to produce ammonia according to the following chemical equation: N 2 + H 2 (g)→2 NH 3 (i) Calculate the mass of ammonia produced if 2.00×10 2 g di nitrogen react with 1.00×10 3 g of dihydrogen. (ii) Will any of the two reactants remain un reacted? (iii) If yes, which one and what would be its mass? Ans : (i) 28.0 g of N 2 require 6.0 g of H 2 to produce =34.0 g of NH 2.00 × 10³ g of N 2 will produce = 28/34 ×2.00×10³g of NH 3 =2.43×10³ g of NH 3 = 2430 g NH 3 (ii) Yes, dihydrogen will remain un reacted to some extent. (iii) Amount of hydrogen that remains un reacted. 28.0 g of N 2 require 6.0 g of H 2 2.00 g×1...

Search This Blog

Knowledge hub